Photonic Integrated Frequency Combs for Space Science Mission Applications

To celebrate the completion of validation testing for our space microcombs, we have put together an overview of our project with the European Space Agency, Miniaturised Frequency Comb for Science Mission Applications (MiCoSMic), and our ongoing development of a two comb optical system for space science.  Why space science satellites can use optical combs Space science depends on precise, efficient instrumentation engineered for use under specific environmental constraints. High-resolution spectrometers are essential for broadening the range of astrophysical objects from which data can be obtained. To identify chemical signatures, star systems, and exoplanets, these spectrometers must maintain high accuracy. Achieving and raising this level of accuracy is an ongoing challenge for space tech. The ideal calibration sources for spectrometers should provide a high density of bright, regularly spaced optical lines. They should have a broad bandwidth coverage and be ultra-stable. Gas emission lamps, the industry standard, suffer from long-term instability and irregularly-spaced spectral lines.  An alternative is to use an optical frequency comb as the calibration source. Optical frequency combs consist of a series of equally spaced mutually coherent wavelengths of light, often referred to as comb lines. Comb sources provide the characteristics required for in-flight recalibration and monitoring, but so far they have been too bulky and too power hungry to fly on board. Miniature and efficient optical combs are a promising alternative. System schematics of where integrated optical frequency combs can enhance space science instrumentation. When performing measurements in the terahertz region of the electromagnetic spectrum, heterodyne detection techniques are often the only practical approach. These frequencies lie beyond the bandwidth of conventional direct-detection systems, making it difficult to observe the weak signals emitted by sources such as the interstellar medium. Heterodyne detection requires a local oscillator, which is a stable reference signal that helps measure incoming radiation. By mixing the two together, the high-frequency signal is shifted down to a lower frequency, where it can be easily measured using standard electronics. Oftentimes, local oscillators consist of a complex chain of electronic frequency multipliers and amplifiers that are cascaded in order to generate the required carriers.  Again, optical comb sources offer an alternative technological solution. Suitable carriers can be generated through the optical heterodyning of two comb lines from an optical frequency comb, producing a signal at their frequency difference. The spacing between these comb lines, known as the free spectral range (FSR), determines the range of frequencies that can be generated in this way, and can vary from GHz in gain-switched combs to THz in dissipative Kerr soliton (DKS) combs, depending on the comb generation mechanism and device design. Both comb technologies can be implemented using photonic integrated circuits (PICs), enabling compact and scalable solutions that offer significant reductions in size, weight, power, and cost (SWaP-C). How our photonic chips make for innovative optical combs In MiCoSMic, we are utilising two different comb technologies to develop hardware that can meet the demands of these two application areas. The first is a DKS comb, generated through the high power optical pumping of a silicon nitride micro-ring resonator. This comb platform allows for the generation broadband frequency combs, with beyond an octave of spectral coverage possible. Within MiCoSMic, the FSR of our microcomb is 383 GHz, with this dependent on the physical geometry of the micro-ring resonator itself. The broad spectral coverage and equally spaced comb lines make this comb technology the ideal candidate for use as a calibration source for optical spectrometers, replacing the need to use multiple gas emission lamps to achieve the same coverage. A standalone microcomb module has been developed, and was tested as part of the spectrometer calibration application validation tests. Optical microcombs in early testing at Pilot. Gain-switched optical frequency combs, the second comb technology utilised within MiCoSMic, provide complimentary trade-offs to DKS. Generated through the direct modulation of the DC bias of a semiconductor laser around its threshold using a high power RF signal, gain-switched combs provide a more flexible comb than our DKS comb. The frequency of the RF signal used for gain-switching determines the FSR of the comb, allowing for a high degree of tunability and accuracy when selecting the comb line spacing. However, the spectral bandwidth of these combs is more limited, usually only covering a number of nanometres. Within this project, we demonstrate a hybrid optical frequency comb achieved by injection-locking a DKS comb and a gain-switched comb to offer attractive features of each comb; broad bandwidth from the DKS comb, and precise flexible frequency operation from the gain-switched comb. The terahertz frequency carriers, suitable for use as local oscillators, are generated via optical heterodyning. Optical heterodyning mixes two optical signals on a fast photodiode to produce an electrical signal equal to their frequency difference. The mutual phase coherence between comb lines results in carriers with reduced RF linewidth, and improved frequency stability and phase performance compared to carriers generated from independent laser sources. An additional Terahertz Module has been developed to support the generation of the gain-switched comb. Both the Microcomb Module and the Terahertz Module will be tested in unison to generate carriers in the 0.6 – 1 THz range. Together, these approaches highlight the versatility of optical frequency combs, combining broad spectral coverage, high stability, and flexible operation. By leveraging the complementary strengths of different comb technologies, MiCoSMic demonstrates a pathway towards compact, high performance sources capable of meeting the demanding requirements of both spectrometer calibration and terahertz heterodyne detection. Furthermore, the integration of these technologies onto photonic integrated circuits (PICs) offers a clear route towards significant SWaP reductions, enabling more compact, efficient, and scalable solutions for future space and sensing applications. Validation testing of the modules at Maynooth University (left) and the Royal Belgian Institute for Space Aeronomy (right). See you at ICSO? Following design, manufacture and preliminary functionality testing, the modules have now finished testing with our validation partners in the project.  Royal Belgian Institute for Space Aeronomy (BIRA-IASB), based in Brussels, tested the optical frequency comb source as a calibration source for

Unlocking Optical Parallelism for the Everything Over Optical™ era

Pilot Photonics’ Hybrid Laser Breakthrough As the demand for AI acceleration, cloud computing, and disaggregated architectures intensifies, traditional copper interconnects are reaching physical limitations. At Pilot Photonics, we’re heralding the Everything over Optical™ era by addressing a critical bottleneck in data scaling: the need for high-power, multi-wavelength optical sources. The Copper Interconnect Bottleneck Copper interconnects are increasingly inadequate for supporting the exponential growth in bandwidth required by next-generation data centre architectures. At high data rates, the reach of copper interconnects fall dramatically, while the power needed to drive the signals increases substantially  Optical interconnects, in contrast, offer: The need for change is evident: scalable, efficient, multi-terabit optical interconnects are essential for future connectivity. Bridging the Gap: From Scale-Out to Scale-Up We’ve already made the first leap — most modern data centres already rely on optical links such as CWDM4, PSM4, and DR4 to scale-out between racks and clusters, replacing copper in many mid-reach connections. But the next frontier is scale-up: bringing that same optical efficiency inside the system, between accelerators, memory pools, and compute tiles. Many of the longer links inside the data centre today use four wavelength coarse wavelength division multiplexing (CWDM4). However due to dispersion at high data rates, CWDM with its broad wavelength spacing does not scale well. To continue to meet escalating bandwidth demands, particularly in the scale-up segment, optical links must increase wavelength counts, from today’s common 4 wavelength links to 8, 16, or even higher.  The industry is now converging on CW-WDM multi-source agreement, allowing denser channel spacing, as shown in the diagram below.   Two primary approaches for the optical source are prevalent in this drive to higher channel count optical links: Laser arrays and comb lasers are each potential solutions to the copper interconnect bottleneck, but each have their own challenges and limitations A Hybrid Solution: ExCELS™ Pilot Photonics is developing a hybrid solution—ExCELS™ (External Comb-Enhanced Laser Source)—that combines the strengths of both approaches. By integrating a high-accuracy microcomb with a high-power laser array through optical injection locking, ExCELS™ delivers: Injection Locked Comb Demultiplexing for Enhanced Performance Our patented chip-scale micro-resonator combs, combined with integrated demultiplexing and amplification, enable a significant increase in comb line power and a substantial improvement in RIN compared to the traditional solution of a SiN comb with passive demultiplexing. This advancement translates to a capacity boost in high-performance applications such as co-packaged optics (CPO), optical I/O systems as well as traditional pluggable optics. Testing has shown greater than 3X capacity improvement, for the same received optical power. For CPO, the technology will be implemented in OIF-compliant External Laser Small Formfactor Pluggable (ELSFP), ensuring seamless integration into CPO infrastructure. Pilot’s solution delivers a significant improvement in RIN CW-WDM Product Portfolio Pilot Photonics is commercializing CW-WDM MSA focused products: Both platforms are flexible, customizable, and ready to support AI-scale networking, system prototyping, and future data centre deployments. Join us as we enable the Everything over Optical™ era.Contact us at sales@pilotphotonics.com

Pilot Photonics Enabling single-chip photonic integrated circuits with comb-enhanced capabilities at wafer scale, today.

Can’t get enough?

Subscribe for exclusive updates and to get more informations